The resistance in the branch with a current of 20mA is 10 ohms, and the resistance in the branch with a current of 10mA is 20 ohms.
What is the resistance about?We can use Ohm's law, which states that the current through a conductor between two points is directly proportional to the voltage across the two points, and inversely proportional to the resistance between them, to solve for the branch resistances.
I = V / R
Let R1 be the resistance in the branch with a current of 20mA and R2 be the resistance in the branch with a current of 10mA.
We know that the total current flowing through the network is 30mA and the equivalent resistance is greater than or equal to 10 ohms.
R_eq = (R1 + R2) >= 10 ohms
We also know that the current flowing through the two branches is equal to the total current flowing through the network.
I = I1 + I2
30mA = 20mA + 10mA
Now we can use the above equations to find the resistance of the two branches.
R1 = V / 20mA
= 10 ohms
R2 = V / 10mA
= 20 ohms
Learn more about ohms law from
https://brainly.com/question/231741
#SPJ1
See correct question below
A current of 30 mA is to be divided into branch currents of 20mA and 10mA by a network with an equivalent resistance equal to or greater than 10 ohms. Obtain the branch resistances.
Consider a simple pendulum and compute the magnitude of the restoring force if the mass of the pendulum is 2 kg and the length of the pendulum is 0.5 m. Assume the pendulum is at the surface of the earth at sea level.
The magnitude of the restoring force if the mass of the pendulum is 2 kg and the length of the pendulum is 0.5 m. The answer is ∣Fres ∣=9.81 sin θ Nm.
How to find out the pendulum is at the surface of the earth at sea level.?We are given:
g = 9.8 m/s ^2 - acceleration due gravity
m = 2 kg - mass of body attached on the string
l = 0.5 m - length of pendulum
Required.
We are asked to find the magnitude of the restoring force under given conditions.
Step2:
First, we need to consider a given situation. In our case, we have a simple pendulum with a mass of the pendulum that is 2 kg, and a length of the pendulum is 0.5 m. Important to emphasize is that the observed pendulum is at the surface of the earth at sea level.
The restoring force for the pendulum has the units of the moment (generally restoring force need not have units of force) and depends on the angle that the pendulum closes with the vertical.
∣Fres ∣=m g l sin θ
Step3:
Finally, we need to substitute known values into equation (1) and solve it.
Calculation method.
∣Fres ∣=m g l sin θ
= (2 kg) (9.80 m/s^2) (0.5 m) sin θ
=19.6 N (0.5m) sin θ
=9.80 sin θ N m
The magnitude of the restoring force is ∣Fres ∣=9.81 sin θ Nm
To learn more about pendulum refers to;
brainly.com/question/3029874
#SPJ4
1. A steel container expands in volume 1% when the pressure with in it is increased by 70Mpa. At standard pressure, it holds 8kg of water; =1000kg/m3. For K=2.05Gpa, when it is filled, how many kilograms of water must be added to increase the pressure to 70Mpa (gage)?
0.268 kg of water must be added to increase the pressure to 70 Mpa (gage).
Solving for how many kilograms of water must be added to increase the pressure to 70 Mpa (gage):To find the amount of water needed to increase the pressure to 70Mpa, we need to use the formula:
Change in volume = (Initial volume) x (Change in pressure)
Young's modulus
The initial volume of the container is 8 liters, since the container holds 8kg of water at standard pressure and the density of water is 1000 kg/m³.
So, change in volume = 8 x 10⁻³ m³
We know that the container expands by 1% when the pressure inside it is increased by 70 MPa, and we want to find the amount of water needed to increase the pressure to 70 MPa.
So, Change in pressure = 70 MPa
Young's modulus (K) = 2.05 GPa
Therefore, Change in volume = (8 x 10⁻³) x (70 / 2.05 x 10^9) = 2.68 x 10⁻⁵ m³
To find the amount of water needed to increase the pressure to 70 MPa, we need to multiply the change in volume by the density of water.
So, amount of water needed = (2.68 x 10⁻⁵) x (1000) = 0.268 kg
Therefore, 0.268 kg of water must be added to increase the pressure to 70 Mpa (gage).
Learn more about Calculations on kilograms on
https://brainly.com/question/13729893
#SPJ1
With 3-phase motor drives that use SCR 6-pulse (6-diode)rectifiers, only one SCR can be on at any given timetrue or false
False. With 3-phase motor drives that use SCR 6-pulse (6-diode)rectifiers, multiple SCRs can be on at any given time. The SCRs are connected in a bridge configuration, which allows for multiple SCRs to be on at the same time.
This allows for the motor drive to be more efficient, as it can draw power from multiple sources at the same time. Additionally, this configuration allows for the motor drive to be more reliable, as it can draw power from multiple sources in the event of a failure of one of the SCRs. SCR 6-pulse (6-diode) rectifiers are a type of rectifier used in 3-phase motor drives. These rectifiers are composed of six SCRs (silicon-controlled rectifiers) connected in a bridge configuration. This configuration allows for multiple SCRs to be on at the same time, which allows for the motor drive to be more efficient and reliable. The SCRs are used to convert the alternating current (AC) power from the power source into direct current (DC) power, which is then used to power the motor.
Learn more about SCRs here
https://brainly.com/question/30287469
#SPJ4
if the handle of an installed motor starter is in the center position, what condition does this indicate?
The two essential parts of a magnetic motor starter are an overload relay and a magnetic contactor.
A solenoid relay known as a magnetic contactor is made up of an inductive coil that is wrapped around a magnetic core, moveable contacts that are connected to movable armatures, stationary contacts that are linked in series with the lines to the motor, and moveable contacts that are linked to stationary contacts. When an electric current is passed through the wire coil, a magnetic field is created. The moving contacts cross the gap between the stationary contacts as a result of the armature being drawn into this field, starting the motor. A spring continuously tries to open the connections, but as long as there is voltage at the coil, magnetic forces will win out.
Learn more about A solenoid relay here:
https://brainly.com/question/29555229
#SPJ4
neglecting the size of the ball, determine the magnitude va of the basketball's initial velocity. (figure 1) express your answer to three significant figures and include the appropriate units.
The trajectory displayed is followed by a basketball as it is thrown at an initial speed of 8.5 m/s.
Explain about the initial velocity?Any object will accelerate as a result of forces acting on it. This acceleration causes a change in the object's velocity. The object's initial velocity is hence its speed prior to the change brought on by acceleration.
The time required is 3 seconds if the terminal velocity of the person is 10 meters per second and the acceleration is 2 meters per second. How fast did that person start moving? u= 10+6 = 16m/s.
When gravitational force is first exerted on an item, its initial velocity indicates how quickly it moves. The final velocity, on the other hand, is a vector number that gauges the speed and direction of a moving object after it has experienced its maximum acceleration.
To learn more about initial velocity refer to:
https://brainly.com/question/24493758
#SPJ4
write a method that takes 2 coordinates in a 2d plane (x, y coordinates) and computes the distance between these two points, according to the distance formula, which is as follows: distance formula this method must be named distance() and it must have 4 int parameters. the first parameter will be the x-coordinate of the first point, the second parameter will be the y-coordinate of the first point, the third parameter will be the x-coordinate of the second point, and the fourth parameter will be the y-coordinate of the second point. this method must return a double. calling distance(0, 5, 0, 0) would return 5.0. you can call your method in the program's main method so you can test whether it works, but you must remove or comment out the main method before checking your code for a score.
The number of times the second string appears in the first string is returned by a method that takes two String inputs.
In computer programming, a string is often a collection of characters, either as a literal constant or as a kind of variable. Both the former and the latter have movable parts and lengths (after creation). A string is often implemented as a character-encoded array of bytes (or words) that stores a succession of components, usually characters. Typically, a string is considered to be a type of data. Another sequence (or list) data types and structures, such as more general arrays, can also be represented by a string. When a variable is defined to be a string, memory space may be statically allocated for only as long as that variable can be, or it may employ dynamic allocation.
Learn more about String here:
https://brainly.com/question/29352925
#SPJ4
determine each component within the microphone-to-multitrack signal flow in your system, and present it in the form of a block diagram.
In our diagram, the microphone(s) convert sound waves into an electric current by receiving them from the sound source (through the process of transduction).
How is a microphone signal produced?In our diagram, the microphone(s) convert sound waves into an electric current by receiving them from the sound source (through the process of transduction). The console pre amps receive the electric signal that was created when the audio signal was transformed to an electric signal.Incoming audio, inserts (where your plug-ins go), sends, a pan, and an output level fader are the typical orders in which the signals flow via channel strips in DAWs.The sequence of actions a sound takes is known as the signal flow. Before the sound is sent back through the speakers during the recording of an instrument, it goes through a number of steps.To learn more about sound source refer to:
https://brainly.com/question/15107447
#SPJ4
The Code reference that specifies the required number of receptacles in a hallway located in non-dwellings is ___. Select N/A (not applicable) if there is not a Code reference for this.
Select one:
a. 210.52(H)
b. 210.52(A)(3)
c. 210.60(B)
d. 210.70(A)(2)(a)
e. none of these
210.70(A)(2)(a) is a Code reference that specifies the required number of receptacles in a hallway located in non-dwellings. According to this Code reference, a hallway located in a non-dwelling must have at least one receptacle outlet for every 12 feet of hallway length.
This Code reference also specifies that the receptacles must be installed at least 6 feet above the floor and must be accessible. This Code reference is applicable to all hallways located in non-dwellings, including those in commercial and industrial buildings. Additionally, this Code reference specifies that the receptacles must be of the type specified in 210.70(A)(2)(b). This Code reference also specifies that the receptacles must be installed in accordance with the manufacturer's instructions and must be protected by a ground-fault circuit interrupter (GFCI). Finally, this Code reference specifies that the receptacles must be installed in a manner that prevents the use of an extension cord.
Learn more about Code reference here
https://brainly.com/question/24174389
#SPJ4
1. (This is from Review Exercise R4.1 at the end of Chapter 4 of Java for Everyone.) Assume variables SimpleWriter out and int n are already declared in each case. Write a while loop that prints:
a. All squares less than n. For example, if n is 100, print 0 1 4 9 16 25 36 49 64 81.
b. All positive numbers that are divisible by 10 and less than n. For example, if n is 100, print 10 20 30 40 50 60 70 80 90.
c. All powers of two less than n. For example, if n is 100, print 1 2 4 8 16 32 64.
2. (The first four of these are from Review Exercise R4.3 at the end of Chapter 4 of Java for Everyone). Using the kind of tracing tables discussed in Writing and Tracing Loops, provide tracing tables for these loops:
Inside of this, the two integer variables "squ" and "n" are defined, and then three while loops are introduced. without the header file.
The following list of values that can be calculated using the loop is: Both "n" and "squ" variables are utilized in the first while loop; "squ" is used to calculate the square between 1 and 100 while "n" is used to check the range. The second is that only the n variable is utilized in this case, which calculates the value and checks its range, whereas it is used to calculate the positive integer that is divisible by 10. The loop, which is used to calculate the double of the number, which is in the range of 1 to 100, is utilized in the last while.
Learn more about Integer variables here:
https://brainly.com/question/14521269
#SPJ4
given the wheelbase of the car 138.8 inches, trackwidth 75 inches and loads on tires as follows. determine the longitudinal cg location in inches measured from the front wheel,
Wheelbase, trackwidth, and tire load data can be used to determine the longitudinal CG location. The distance in inches between the center of gravity and the front wheel.
Wheelbase, trackwidth, and tire load data can be used to determine a car's longitudinal center of gravity (CG) location. The distance between the centers of the front and rear wheels is known as the wheelbase, while the distance between the left and right tire centerlines is known as the trackwidth. The amount of weight on each of the four tires that are in contact with the ground is known as the tire load. The entire weight of the vehicle is divided by the wheelbase and trackwidth, and the resulting number is multiplied by the wheelbase to determine the longitudinal center of gravity (CG) location. The resultant measurement, taken from the front wheel, is the longitudinal CG location in inches.
Learn more about distance here-
https://brainly.com/question/19915401
#SPJ4
For each of the four types of organizations shown, rate the importance of each factor in terms of making location decisions using L low importance, M moderate importance, and H high importance.
The rating of the Local bank -Steel Mill - Food Warehouse - Private school are:
Factors:
Convenience - M L L H
Display area - L H M L
Operating cost - H H H M
Clustering - L H M M
What is the rating about?Convenience: For a local bank, convenience for customers is moderately important, but for a steel mill or food warehouse, it's less important. For a private school, it's high importance.
Display area: For a local bank, display area is not important, but for a steel mill, it's high importance, for a food warehouse is moderate importance, and for a private school it's low importance.
Operating cost: For all the types of organization, operating cost is high importance.
Clustering: For a local bank, clustering is less important, for a steel mill is high importance, for a food warehouse is moderate importance, and for a private school it's moderate importance.
Note: This rating is based on the assumption that the organizations are looking to make a location decision, and these are the factors that are considered most important for them. The importance of each factor can vary depending on the specific situation, and other factors not listed here may also be important.
Learn more about rating from
https://brainly.com/question/29353028
#SPJ1
determine the circulation for the given vector field around the enclosed half circle of radius 1.
To determine the circulation for the given vector field around the enclosed half circle of radius 1, we need to calculate the line integral of the vector field along the boundary of the half circle.
The line integral is calculated by integrating the dot product of the vector field and the differential of the boundary. The circulation is then equal to the line integral divided by 2π. To calculate the line integral, we need to know the vector field and the boundary of the half circle. Once we have this information, we can use the equation for the line integral to calculate the circulation.
To calculate the circulation for the given vector field around the enclosed half circle of radius 1, we need to first calculate the line integral of the vector field along the boundary of the half circle. The line integral is calculated by integrating the dot product of the vector field and the differential of the boundary. The differential of the boundary is equal to the vector from the starting point to the end point of the boundary. The vector field can be expressed as a function of the coordinates of the boundary. Once we have the vector field and the differential of the boundary, we can use the equation for the line integral to calculate the circulation. The circulation is then equal to the line integral divided by 2π.
Learn more about line integral here
https://brainly.com/question/29850528
#SPJ4
Intro to JAVA
If you have a class called IceScraper nested within the class Car, which of these would be the correct way to instantiate an IceScraper object?
a) Car.IceScraper ice_scraper = new Car.IceScraper();
b)IceScraper ice_scraper = new Car.IceScraper();
c) IceScraper.Car ice_scraper = new IceScraper.Car();
d) Car.IceScraper ice_scraper = Car.new IceScraper();
Java is used to create software on many different platforms, including Windows, Mac OS, and the various versions of UNIX. The correct syntax is Car.IceScraper ice_scraper = Car.new IceScraper();
What is mean by JAVA?
Java is an object-oriented programming language used widely in creating applications for internet and web development. It was created in 1995 by Sun Microsystems, which was later acquired by Oracle. Java is a popular language because it is simple to learn and use, and it is secure, reliable and efficient. It also has a large library of existing code that can be reused, making development easier and faster. Java is an interpreted language, meaning that the code is compiled and interpreted by the Java Virtual Machine (JVM).
This makes Java applications more portable than other languages, since the code does not need to be recompiled for each platform.
To learn more about java program refer to:
brainly.com/question/26789430
#SPJ4
Problem 2. How many bits are needed to store the following data? (8 points)
a. String of 6 ASCII characters
b. Decimal number equal to 27
c. Binary number equal to 1010101
d. One Kilobyte (KB) of data
String of 6 ASCII characters are needed to store the following data.
how many bits can something be stored?In three bits, there are 2 * 2 * 2 values , or 8. and so forth. Thus, at least two bits are required to hold three values. To store more than 256 values, you do indeed require more than 8 bits, as 28 equals 256.8 bits make up one byte. The usage of hex form is a more condensed method for humans to record lengthy bit strings (hex is just notation; the bit string still consists of 0s and 1s inside the machine). Groups of 4 bits each make up the bit string's division.To learn more about bits refer to:
https://brainly.com/question/19667078
#SPJ4
to practice problem-solving strategy 15.1 mechanical waves. waves on a string are described by the following general equation y(x,t)
The transverse displacement will be 0.089963 m. The velocity of the shear wave particles is orthogonal to the direction of the wave.
What is transverse displacement?
Here given the data
Then the equation y(x,t)=Acos(kx−ωt)
speed (v) = 9.00 m/s
amplitude (A) = 9.00 × 10^−2 m
wavelength (λ ) = 0.480 m
We have to find out transverse displacement.
Here we know that.
v = angular frequency / wave number
also wave number = 2 / λ
= 2 / 0.480
= 13.0899
angular frequency = v x k
angular frequency = 9.00 × 13.0899
angular frequency = 117.8097 rad/sec
= 118 rad/sec
Therefore, the equation y(x,t)=Acos(kx−ωt)
y(x,t)=9.00 × 10^−2 cos(13.0899 x−118t)
If x =0 and and t = 0
Then, maximum y(x,t)= 9.00 × 10^−2 cos(13.0899 (0) − 118 (0))
= 9.00 × 10^−2 m
if x = 1.59 m and t = 0.150 s
Then,
y(x,t) = 9.00 × 10^−2 cos(13.0899 (1.59) −118(0.150) )
y(x,t) = 9.00 × 10^−2 × (0.99959)
y(x,t) = 0.089963 m
Therefore the transverse displacement is 0.089963 m
The complete question:
" To practice Problem-Solving Strategy 15.1 Mechanical Waves. Waves on a string are described by the following general equation y(x,t)=Acos(kx−ωt). A transverse wave on a string is traveling in the +x direction with a wave speed of 9.00 m/s , an amplitude of 9.00×10−2 m , and a wavelength of 0.480 m . At time t=0, the x=0 end of the string has its maximum upward displacement. Find the transverse displacement y of a particle at x = 1.59 m and t = 0.150 s ."
To learn more about transverse displacement refer to :
brainly.com/question/28200873
#SPJ4
T/F the progress bar indicates how many concepts you have completed, how many are in progress, and how many are still left in the assignment.
The progress bar indicates how often concepts that have completed, how many still are in progress, and how many are left in the assignment, indicating that the given statement is true.
What is progress bar?The progress bar on your assignment page is an excellent way to monitor your progress.It shows how many concepts you've finished, how many are currently in progress, and how many are still outstanding. Knowing this information will assist you in planning and prioritizing your tasks, allowing you to complete the assignment on time and to the best of your ability.The assignment tracker's progress bar is a great way to keep track of your progress. It shows how many concepts you've completed, how many are in progress, and how many are still outstanding.Therefore, The progress bar displays how many concepts you have completed, how many are still being worked on, and how many are left in the assignment.To learn more about progress bar refer to :
https://brainly.com/question/30279148
#SPJ4
patient sustained a stab wound to the right neck during a domestic dispute and underwent wound exploration. the stab wound was extended, and examination of surrounding bones, connective tissue, muscles, and nerves revealed normal findings. no foreign bodies were found. the area was debrided and irrigated. coagulation of minor subcutaneous and muscular blood vessels was achieved with electrocautery. the wound was cleaned and closed with 3-0 vicryl.
To achieve wound hydration, eliminate deeper debris, and help with the visual examination, a solution is continuously pumped across an open wound surface.
When is wound irrigation used?
Wound irrigation is recommended for the management of both acute and chronic wounds, particularly those that will be sutured, repaired surgically, or debrided. Irrigation is the process of pouring a liquid solution over an open wound to better see the wound and to help clear debris from the deeper areas of the lesion. Debridement is the process of removing unhealthy or infected tissue to speed up the healing of wounds. In arid locations and during periods of below-average rainfall, irrigation aids in the growth of crops, upkeep of landscapes, and regreening of disturbed soils.
Irrigation is used for these purposes as well as to protect crops from frost, control weed growth in grain fields, and avoid soil consolidation.
To learn more about surface refer to:
https://brainly.com/question/4580651
#SPJ4
suppose an uncharged solid steel ball, for example, one of the steel balls used in an old-fashioned pinball machine, is resting on a perfect insulator. some small amount of negative charge (say, a few hundred electrons) is placed at the north pole of the ball. if you could check the distribution of the charge after a few seconds, what would you detect?
After a few seconds, you would detect that the negative charge has spread out over the entire surface of the steel ball. This is because steel is a good conductor of electricity, so the charge quickly distributes itself evenly over the metal surface.
What factors would affect the charge distribution on the surface of the steel ball?The charge distribution on the surface of the steel ball would be affected by several factors. The material properties of the steel ball, such as its electrical conductivity and dielectric constant, would affect how the charge is distributed. The distance between the charged particle and the steel ball, as well as the size of the steel ball, would also be important factors. The presence of any other charged particles or electric fields in the vicinity of the steel ball would also affect the charge distribution. Finally, the shape of the steel ball would also have an effect on the charge distribution, as the charge would tend to be more concentrated at certain points than others.To learn more about charge distribution refer to:
https://brainly.com/question/16242927
#SPJ4
A large rock became visible to a driver at a distance of 175 ft. Assuming a perception-reaction time of 0. 8 s, an initial speed of 42 mi/h, a coefficient of friction of 0. 5, and a level roadway, calculate the speed at impact
Answer:
Assuming a perception-reaction time of 0.8 s, an initial speed of 42 mi/h, a coefficient of friction of 0.5, and a level roadway, calculate the speed at impact.
Explanation:
what is situations would it be possible to use a utp cable standard such as 1000base-cx instead of a fiber-optic cable standard such as 1000base-lx or 1000base-t?
If the 1000BASE-T Ethernet connection's allowed distance limitation is disregarded.
For infrastructure applications, Cat 5e utp cable models are created; they give the networks that use them the ability to send data securely, without packet loss, and without any speed loss during operations. Both specify Ethernet connection, but 1000BASE-T at 1 Gb/s. Additionally, both are made to operate on up to 100 meters of four-pair, 100 ohm-impedance twisted-pair cables. We can infer from this data that the transmission speed will decrease significantly if the 1000BASE-T Ethernet connection's permitted distance constraint is disregarded and the frames are sent across a 300 meter Cat5e cable segment. The transmission speed will decrease noticeably if the 1000BASE-T Ethernet connection's permitted distance limitation is disregarded and the frames are delivered over a 300-meter Cat5e cable segment.
Learn more about 1000BASE-T here:
https://brainly.com/question/27204453
#SPJ4
Question 4
The removeElement method is intended to remove all instances of target from the ArrayList object data passed as a parameter. The method does not work as intended for all inputs.
public void removeElement(ArrayList data, int target)
{
for (int j = 0; j < data.size(); j++)
{
if (data.get(j).equals(target))
{
data.remove(j);
}
}
}
Assume that the ArrayList object scores and the int variable low_score have been properly declared and initialized. In which of the following cases will the method call removeElement(scores, low_score) fail to produce the intended result?
The removeElement method will fail to produce the intended result in the following cases:
If the ArrayList object scores contains more than one instance of the same value as low_score, only the first instance will be removed and the other instances will remain in the list.If the ArrayList object scores contains any elements whose type is not compatible with the type of lowscore (e.g. if lowscore is an integer and scores contains a String), the method will throw a ClassCastException.If the ArrayList object scores contains any elements that are null, the method will throw a NullPointerException.Learn more about The removeElement method:
https://brainly.com/question/14190464
#SPJ4
Need help to answer.
ASAP.
A furnace wall consists of 125 mm wide refractory brick and 125 mm wide insulating firebrick separated by an air gap. The outside wall is covered with a 12 mm thickness of plaster. The inner surface of the wall is at 11000C and the room temperature is 250C. The heat transfer coefficient from the outside wall surface to the air in the room is 17 W/m2K, and the resistant to heat flow of the air gap is 0. 16K/W. The thermal conductivities of refractory brick, insulating firebrick, and the plaster are 1. 6, 0. 3, and 0. 14 W/mK respectively. Calculate:
(i) the rate of heat loss per unit area of wall surface;
(ii) the temperature at each interface throughout the wall;
(iii) the temperature at the outside surface of the wall.
The temperature at the outside surface of the wall is 1344 0.8 watts.
What is the temperature at the outside surface of the wall?Determine the loss rate per square foot of the wall surface. Our refractor block brick's thermal resistance is equal to B divided by K. A times one. Thus, this is equal to 1.6 times one divided by 12.5 times 10 to the negative three. Our air gap contributes 0.16 K per W to our thermal resistance. We have three fire bricks as a result. Three divided by K gives us B. A thrice. This equals 0.3 times one divided by 1 25 times 10 to the negative three. Because of our plaster, four equals four divided by B divided by K.Four times our area is equal to 12 x 10 3 / 30.14 x 1 or 4 times our area. Furthermore, our thermal resistance is not equal to one divided by H but rather by A due to the heat transfer from the outside. This makes 1/7. The reason why adding R. One plus R. A plus R. three plus our four plus are ineffective is because of our total net thermal resistance. We thus obtain 0.799 K per W. The rate of heat loss throughout our entire surface area, Q, is equal to T. W minus T. Zero divided by R, or 111 100 minus 25 divided by 0.799, which is 1344 0.8 watts.To learn more about loss rate refer to:
https://brainly.com/question/16556041
#SPJ4
questiona test car and its driver, with a combined mass of 600 kg, are moving along a straight, horizontal track when a malfunction causes the tires to stop rotating. the car skids to a halt with constant acceleration, leaving skid marks on the road during the whole time it skids. which two of the following measurements, taken together, would allow engineers to find the total mechanical energy dissipated during the skid? select two answers.
The two measurements that, taken together, would allow engineers to find the total mechanical energy dissipated during the skid are:
A. The length of the skid marks
C. The coefficient of static friction between the tires and the track.
The length of the skid marks can be used to determine the distance over which the car decelerated and came to a stop.
This distance, combined with the car's mass, can be used to calculate the work done by the friction force (which is equal to the mechanical energy dissipated) using the equation:
Work = force x distance
The coefficient of static friction between the tires and the track is necessary to calculate the friction force.
The friction force can be determined using the equation:
Friction force = coefficient of static friction x normal force
The normal force can be calculated from the car's mass and the acceleration due to gravity.
By combining the length of the skid marks (distance) with the coefficient of static friction, engineers can determine the total mechanical energy dissipated during the skid.
Hence, option A and option C are correct.
To learn more on Force click here:
https://brainly.com/question/13191643
#SPJ12
Complete question:
A test car and its driver, with a combined mass of 600 kg, are moving along a straight,horizontal track when a malfunction causes the tires to stop rotating. The car skids to a halt with constant acceleration, leaving skid marks on the road during the whole time it skids. Which two of the following measurements, taken together, would allow engineers to find the total mechanical energy dissipated during the skid?
A. The length of the skid marks
B. The contact area of each tire with the track.
C. The coefficent of static frction between the tires and the track.
D. The coefficent of static frction between the tires and the track.
Which of the following statements are true for artificial intelligence (AI)? [Choose all that apply]
AI focuses on the broad idea of making a system execute a task
Machine Learning or ML is a subset of AI
AI learns on its own without any input data
A self-driving car is an example of AI
Machine learning (ml) and artificial intelligence are the fields where the problem of having too many skilled, business-savvy programmers is least likely to occur (ai).
Machine learning (ML), a subtype of artificial intelligence, is the method by which computers learn to recognize patterns or the capacity to continuously learn from and make predictions based on data, then make adjustments without being specifically programmed to do so. The way that machine learning works is quite complex and depends on the task at hand as well as the algorithm used to do it. But at its core, a machine learning model is a computer that scans data for patterns before applying what it learns to perform the task that has been handed to it more effectively. Even the more challenging tasks can be automated by machine learning if they depend on a set of data or rules.
Learn more about Machine learning (ML) here:
https://brainly.com/question/28144983
#SPJ4
TCL Rosu TV
.
Does anyone know why my stuck is like this?
Try rebooting the router by unplugging it from the power source, then plugging it back in.
Why is my TCL Rosu TV not connecting?Unplug the router from the power supply, then connect it back in to see if that can restart it. Change the wireless security setting on the router to WPA-PSK (TKIP). Check the "Advanced Router Settings" section below by scrolling down.Ten seconds after unplugging your Android TV, plug it back in. Retry pairing it while your Android TV is on. Check to see if your device can link to other gadgets, like a tablet or phone. When connecting to other devices, your device: Restore the factory settings on your Android TV.Restarting any problematic equipment, including your smart TV, is the simplest universal step in troubleshooting. Before plugging the TV back in, wait at least 30 seconds after turning it off and unplugging it from the wall.Learn more about TV not connecting refer to :
https://brainly.com/question/30229078
#SPJ1
from the following list, select all the differences between compression strokes of the actual four-stroke spark-ignition engine and the ideal otto cycle. multiple select question. a spark fires in the ideal compression stroke, whereas it fires later in the actual four-stroke cycle. the ideal otto cycle has isentropic compression, while compression in the actual cycle is not isentropic. the working fluid in the actual cycle is a fuel-air mixture, while it is only air in the ideal cycle. the working fluid tempe in the actual cycle is a fuel-air mixture, while it is only air in the ideal cycle.
The ideal cycle's intake and exhaust strokes are simplified, which is the most noticeable difference between actual four-stroke spark-ignition engine and the ideal otto cycle .
What is ideal otto cycle?The ideal Otto cycle introduces a fuel-air mixture during the induction stroke, compresses it to a much lower compression ratio (around 8:1), and then ignites it with a spark. The combustion causes a sudden increase in pressure while keeping the volume essentially constant.The ideal cycle's intake and exhaust strokes are simplified, which is the most noticeable difference between the two diagrams. Heat Qout is ejected into the environment during the exhaust stroke. The gas leaves the engine and is replaced by a new mixture of air and fuel in a real engine.An Otto cycle is a simplified thermodynamic cycle that describes how a typical spark ignition piston engine works.To learn more about ideal otto cycle refer to :
https://brainly.com/question/23723039
#SPJ4
FILL IN THE BLANK When a non-motor-operated electrical appliance lacks an overcurrent protective device rating, NEC 422.11(E) states that the branch circuit overcurrent protection shall be ____.
TRUE, additional overcurrent protection is utilized for equipment's internal circuits and parts, as well as for luminaires, appliances, and other types of equipment.
It shall be permitted to function as a substitute for needed branch-circuit overcurrent devices or in place of the required branch-circuit protection. When supplemental overcurrent protection is applied for internal circuits and equipment parts, it must not be used in place of the essential branch-circuit protection or as a replacement for needed branch-circuit overcurrent devices on luminaires, appliances, and other equipment. Additional overcurrent protection devices are not required. Each ungrounded conductor needs to have a series-connected fuse, overcurrent trip device, or circuit breaker. A current transformer and an overcurrent relay together make up an overcurrent trip device.
Learn more about Overcurrent here:
https://brainly.com/question/30329005
#SPJ4
technician a says all differentials are vented. technician b says that a clogged vent can cause the rear axle seal to leak. which technician
Technician B is correct. Differentials are typically vented to allow air to escape and prevent pressure from building up inside the differential.
If the vent becomes clogged, the pressure inside the differential can build up and cause the rear axle seal to leak. This can lead to oil leaking from the differential, which can cause damage to the differential and other components. It is important to check the vent regularly to ensure that it is not clogged and that the differential is operating properly. Differentials are a type of gearbox used in vehicles to transfer power from the engine to the wheels. They are typically made up of two or more gears that are connected to each other and to the drive shaft. Differentials are used to allow the wheels to rotate at different speeds, which is necessary when turning a corner. Differentials are also used to provide power to the wheels when accelerating or decelerating. Differentials are typically vented to allow air to escape and prevent pressure from building up inside the differential and are also used in other applications, such as in robotics and industrial machinery.
Learn more about Differentials here
https://brainly.com/question/28098434
#SPJ4
Your biology test is in a few days, and you have to study a large amount of material in order to prepare for it. Define all of the following concepts and explain how each could apply to your situation.a. Declarative memoryb. Semantic memoryc. Mnemonic devicesd. Short-term (working) memory
Short-term memory briefly refers to the record while declarative memory bases itself on names, places, etc., semantic memory bases itself on grammar, and so forth.
The definition of declarative memory?Declarative memory is a sort of memory that is dependent on a particular piece of information, such a name, a certain date, etc.Short-term memory can be described as the memory that maintains information for a brief amount of time, whereas semantic memory is based on the syntactical and grammatical characteristics of a text.In summary, declarative memory refers to names, places, etc., semantic memory refers to grammar, and short-term memory refers to the information for a brief period of time.Short-term memory briefly refers to the record while declarative memory bases itself on names, places, etc., semantic memory bases itself on grammar, and so forth.To learn more about Declarative memory refer to:
brainly.com/question/6652786
#SPJ4
according to siemens enterprise communications, what is one of the most effective routes to stealing confidential data from organizations?
Siemens Enterprise Communications, a German company, claims that social engineering is one of the most efficient ways to obtain private information from businesses.
Which of the following categories of data thieves cannot take from their intended victims? Siemens Enterprise Communications, a German company, claims that social engineering is one of the most efficient ways to obtain private information from businesses.In a recent Siemens test, engineering succeeded in fooling 85% of the office workers.To deceive people and fill up their personal information, such as bank account information, phone numbers, addresses, usernames, and passwords, etc., phishers frequently create fake websites.The most typical phishing fraud involves deceptive tactics.Fraudsters use this ruse to steal people's login information or personal information by pretending to be a reputable business.The most prevalent kind of cyberattack is called malware, which includes a wide range of subtypes such ransomware, trojans, spyware, viruses, worms, keyloggers, bots, cryptojacking, and other attacks that make use of software in a destructive way.To learn more about confidential data refer
https://brainly.com/question/29413269
#SPJ4