Answer:
Hot Working
Explanation:
Given that hot working is carried out at temperatures greater than the recrystallization temperature of the metal, thereby the stress needed for deformation is considerably less.
On the other hand, cold working is carried out at temperatures lesser than the recrystallization temperature of the metal, thereby stress needed for deformation is much higher
Hence, comparing cold working to hot working, flow stress is usually lower in HOT WORKING.
A reservoir is 1 km wide and 10 km long and has an average depth of 100m. Every hour, 0.1% of the reservoir's volume drops through a vertical height of 100 m and passes through turbines to produce electricity with an efficiency of 92%. What is the electrical power output of this facility?
Answer:
250.7mw
Explanation:
Volume of the reservoir = lwh
Length of reservoir = 10km
Width of reservoir = 1km
Height = 100m
Volume = 10x10³x10³x100
= 10⁹m³
Next we find the volume flow rate
= 0.1/100x10⁹x1/3600
= 277.78m³/s
To get the electrical power output developed by the turbine with 92 percent efficiency
= 0.92x1000x9.81x277.78x100
= 250.7MW
Expert Review is done by end users.
Answer:nononononono
Explanation:
1. Drill press size is determined by the largest__
A function is different from a procedure because a functiondoes not contain a set of instructions.can have only a limited number of steps.returns a value.is mathematical.
Answer: A function returns a value and a procedure just executes commands.
Explanation:
Answer:
c - returns a value.
Explanation:
on edge pls mark brainiest
A continuous function y = ƒ(x) is known to be negative at x = 0 and positive at x = 1. Why does the equation ƒ(x) = 0 have at least one solution between x = 0 and x = 1? Illustrate with a sketch
Answer:
69
Explanation:
69420=420659782
fjkdod
How do I answer all the questions on this page?
Answer:
Create a google docs copy everything and paste hope this helps! :)
Explanation:
For three control stations,there should be how many start buttons in parallel with the suxiliary contact
What cell type has no membrane-bound organelles, has DNA that is found in an area called the
nucleoid, and is very small?
A. Eukaryotic cell
B. Prokaryotic cell
C. Animal cell
D. Plant cell
Answer:
Prokaryotic cell
Explanation:
An annealed copper strip of 228 mm wide and 25 mm thick being rolled to a thickness of 20 mm, in one pass. The roll radius is 300 mm, and the rolls rotate at 100 rpm. Calculate the roll force and the power required in this operation
Answer:
The roll force is 1.59 MN
The power required in this operation is 644.96 kW
Explanation:
Given;
width of the annealed copper, w = 228 m
thickness of the copper, h₀ = 25 mm
final thickness, hf = 20 mm
roll radius, R = 300 mm
The roll force is given by;
[tex]F = LwY_{avg}[/tex]
where;
w is the width of the annealed copper
[tex]Y_{avg}[/tex] is average true stress of the strip in the roll gap
L is length of arc in contact, and for frictionless situation it is given as;
[tex]L = \sqrt{R(h_o-h_f)} \\\\L = \sqrt{300(25-20)}\\\\L = 38.73 \ mm[/tex]
Now, determine the average true stress, [tex]Y_{avg}[/tex], for the annealed copper;
The absolute value of the true strain, ε = ln(25/20)
ε = 0.223
from true stress vs true strain graph; at true strain of 0.223, the true stress is 280 MPa.
Then, the average true stress = ¹/₂(280 MPa.) = 180 MPa
Finally determine the roll force;
[tex]F = LwY_{avg}[/tex]
[tex]F = (\frac{38.73 }{1000})(\frac{228}{1000})*180 \ MPa\\\\F = 1.59 \ MN[/tex]
The power required in this operation is given by;
[tex]P = \frac{2\pi FLN}{60}\\\\P = \frac{2\pi (1.59*10^6)(0.03873)(100)}{60}\\\\P = 644955.2 \ W\\\\P = 644.96 \ kW[/tex]